金寶信LED室內外租賃屏安裝說明

LED租賃屏安裝說明

1，檢查單個屏體的單元箱體數量，日子架、連接片，線材，螺絲數量和尺寸是否符合屏體要求（本屏為P2.604屏，500*500*65mm箱體5*5個拼接），用1+1.5米日子架4套，連接片32個，連接片螺絲128個，箱體之間電源線75cm25條，網線75cm25條，3條主電源線，2條主網線，每條主電源線帶8-10個箱體，每條主網線帶8-10個箱體。

2，屏體拼裝，裝屏之前先將每個箱體點亮測試沒問題在往上裝，先將第一排5個箱體左右用鎖扣鎖緊，然后后排每隔一個箱體固定一個1.5米日子架，裝好與要使用的地方，第一排調水平，后面用連接片和螺絲將箱體于日子架固定，然后裝第二排箱體，每隔箱體左右鎖緊，與下排箱體也用鎖扣鎖緊，一次類推裝好3排，然后將1米日子架于1.5米日子架連接好，在裝上面兩排箱體。

3，屏體接線，箱體之間電源線連接按線材和箱體標注符號插線，網線也類同，整屏每兩橫排用1條主電源線和1條主網線，最上面一排用一條主電源線和主網線。

4，通電調試，通電之前先檢查屏體線路是否接錯，確認完無誤然后通電，連接電腦，在電腦上做好屏體程序，然后發送到屏體上面。

5，屏體使用，具體內容操作發布請參展軟件使用說明。

LED rental screen installation instructions

1, check the number of unit housing a single screen, time frame, connector, wire, if the number of screws and conform to the requirements of the screen (the screen for the P2.604 screen, 500 * 500 * 65 mm case 5 * 5 splicing), with 1 + 1.5 meters day 4 sets, connection piece of 32, connection screws 128, power cord article 75 cm25 between casing, line 75 cm25 article, three main power cord, two main lines, each of the main power cord with 8-10 boxes, each main line 8-10 boxes.

2, the screen body assembling, loading screen before each cabinet light test no problem in the jacket, the first row of first five cabinet with lock lock, and then the back every box fixed a time frame, 1.5 meters installed and where to use, the first row of the level, behind the connection plate and screws to fix box in time frame, and then the second row housing, around every cabinet lock, also use lock locking and lower enclosure, an analogy installed 3 row, then 1 m days out of 1.5 m days frame connection, in the above two rows of housing.

3. Wiring of the screen body, the power cord connection between the box body shall be inserted according to the wire and the symbol of the box body, and the network cable shall be similar. One main power cord and one main network cable shall be used in every two horizontal rows of the whole screen, and one main power cord and main network cable shall be used in the top row.

4. Power-on debugging: check whether the circuit of the screen body is connected wrong before power-on, confirm it is correct, then power on, connect the computer, make the screen body program on the computer, and then send it to the screen body.

5, the use of the screen, the specific content of the operation release please show the software use instructions.